Method Statement for Road Marking

1. Introduction and General Information

This method statement consists of construction procedures of Road Marking, including material & machineries to be used, method of constructions, quality control test & verifications, and also the safety precautions to be implemented at site.
1.1. Location of Works
Road marking location will be decided as per the road marking drawings issued by the Engineer.
2. Materials
The major materials used for the road marking.
  • DJ Thermo line thermoplastic road marking materials.
  • Glass beads.
3. Equipment
The major equipment used for Road marking includes, but are not limited to the following.
  • Road Marking Machine.
  • Gas.
  • Rope.
  • Chisel.
  • Cleaning equipment
  • Small Tools.
4. Safety Management and Control

Safety precaution will be taken complying with the Traffic & Safety Plan. Every precaution will be taken to avoid any accidents & damages to adjoining properties, workers, and road users.
All workers will be advised to wear helmets, boots, and gloves while working. There will be a stand by vehicle near site always if needed in a case of accident.
The safety officer inspects several times to inspect safety matters.
5. Method and Procedures
The method and procedures for Road marking will follow the steps below. Flow chart is also provided in appendix A.

5.1 Center line will be set out and get approvals about the center line before commencement of line marking.
5.2 Road surface shall be cleaned manually using wire brush and wash the surface where necessary.
5.3 As per the approved road marking design the road marking lines & symbols will be set out means of white chalk and approval will taken by Engineer.
5.4 The thermoplastic material is heated in the range of temperature around 170 ~ 200 C and maintain in the range during the entire laying process.
5.5 After getting the approval of the temporary marking on the asphalt surface permanent marking shall be carried out by considering required color. This machine has the facility of adding glass beads in to the paint while painting.
5.6 All roads marking shall be protected from traffic until the marked paint get dry.
6. Quality Control
To ensure that the steps of the procedure are fully complied with the activities such as setting out, temporary marking , permanent painting etc. certain inspections and verifications will be carried out as described in the above procedures.

Comments

  1. UnknownJuly 17, 2014 at 10:39 PM

    Wow, I didn't know there was a "method" to road marking. It always seemed like a fairly straight forward, simple labor project. This paints it as kind of an art form. Thiago | http://www.austraklinemarking.com.au

    ReplyDelete
    Replies
    1. AnonymousMarch 30, 2022 at 4:56 PM

      Civil Projects: Method Statement For Road Marking >>>>> Download Now

      >>>>> Download Full

      Civil Projects: Method Statement For Road Marking >>>>> Download LINK

      >>>>> Download Now

      Civil Projects: Method Statement For Road Marking >>>>> Download Full

      >>>>> Download LINK Dq

      Delete
  2. UnknownJanuary 21, 2015 at 11:44 AM

    Thank you for this MS. It helped me to analysis the risk associated

    ReplyDelete
  3. AdminAugust 26, 2015 at 9:01 PM

    thanks for info..it helped me a lot..tq

    ReplyDelete
  4. Pabitha PabiJuly 20, 2017 at 4:10 PM

    This is great one to see your blog last time I see same design to my friend constraction building in chennai. Majorly used Aluminium scaffolding equipment used for glass room design. Really very gud looking.

    ReplyDelete
  5. CodasphaltFebruary 1, 2019 at 5:05 PM

    Nice Blog, Really Good Content, Really Helpfull for us, I have also a Some Great Content For you Guys, so just go through and take benefit of asphalt services

    asphalt sealcoatin

    asphalt repair

    asphalt overlay

    brick paver driveways

    cement curbing

    line striping

    thermoplastic markings

    concrete sidewalks

    ReplyDelete
  6. Aku dan Persinggahan IniJuly 11, 2019 at 1:26 PM

    bingo! i got it

    ReplyDelete
  7. rivercitylinemarkingNovember 5, 2020 at 9:33 AM

    I read this article, it is really informative one. Your way of writing and making things clear is very impressive. Thanking you for such an informative article. Line Removal Service in Brisbane

    ReplyDelete
  8. AnonymousJuly 15, 2021 at 1:38 AM

    This comment has been removed by the author.

    ReplyDelete
  9. Petron ThermoplastAugust 13, 2021 at 4:53 PM

    Thanks to this article about are the information it will be helpful for road marking works.
    PVDF Engineering parts

    ReplyDelete
  10. sjjad110September 12, 2021 at 1:13 AM

    I’ve desired to post about something similar to this on one of my blogs and this has given me an idea. Patio Pavers Boca Raton Cool Mat.

    ReplyDelete
  11. CCESESeptember 14, 2021 at 12:03 PM

    What is DJ Thermo line?

    ReplyDelete
  12. JACKJanuary 17, 2022 at 3:18 PM

    Augustine thanks for sharing this! My extensive google search has now been recently paid for using quality insight to talk about together with our relatives. driving instructors

    ReplyDelete
  13. AnonymousMarch 30, 2022 at 4:55 PM

    Civil Projects: Method Statement For Road Marking >>>>> Download Now

    >>>>> Download Full

    Civil Projects: Method Statement For Road Marking >>>>> Download LINK

    >>>>> Download Now

    Civil Projects: Method Statement For Road Marking >>>>> Download Full

    >>>>> Download LINK

    ReplyDelete
  14. Education InteractionNovember 28, 2022 at 5:52 PM


    PMP Classroom Training from expert practitioners to pass the PMP® exam on your 1st attempt with best practices

    PMP CLASSROOM TRAINING

    ReplyDelete
  15. Aditya RanaOctober 27, 2023 at 11:59 AM

    I like this blog's detailed method for road marking. If you need line marking in Gold Coast, check out Kenex expert solutions to keep roads safe and well-organized.

    ReplyDelete
  16. BraydenDecember 29, 2023 at 11:27 AM

    This comment has been removed by the author.

    ReplyDelete
  17. BraydenDecember 29, 2023 at 11:29 AM

    This comment has been removed by the author.

    ReplyDelete
  18. BraydenDecember 29, 2023 at 1:03 PM

    This comment has been removed by the author.

    ReplyDelete
  19. BraydenDecember 29, 2023 at 1:05 PM

    Your blog about road marking is fantastic! I appreciate how you explain everything clearly. It's super helpful for anyone looking for info on line marking Brisbane Great job!

    ReplyDelete

Post a Comment

Popular Posts

Field Density Test

Image
  The sand cone method is used for field density test in our highway construction. In the field, the dry density test is carried out for check the compaction of layers. Compaction is most useful for the preparation of sub base grade and other pavement layers and in construction of embankment in order to increase the stability and to decrease settlement. In field compaction, the compacting moisture content is first controlled at optimum moisture content and the adequacy of rolling or compaction is controlled by checking the dry density achieved and comparing with the maximum dry density. Base layer-98% Sub base layer-98% Type 1 layer-95% ABC layer-100% Road shoulder- 98% Field density test Testing procedure: The weight of empty sand cone is measured and then filled with dry sand and weighted. The soil excavated from the hole is collected and weighted. After weighting, a specimen of soil is taken to determine it water content. The sand cone is placed on...
Read more

METHOD OF INTERNAL & EXTERNAL PLASTERING ON BRICK WALLS & CONCRETE SURFACES

Method of Plastering. Internal plastering on surfaces of brick and concrete. External wall plastering. Soffit plastering / Soffit finishing with cement based easy plaster material and wall putty. Improving joint of brick walls & structural concrete joints. Internal Plastering on surfaces of Brick and Concrete. Surface where plastering is to be done will be cleaned. Level pegs on walls will be fixed with reference to the off lines to brick walls set out in floors. (Using centre plumb bob and nylon thread). All the brick walls will be watered before pasting mortar on walls. First coat mortar filling (1:4 Cement and Sand) upto 15 mm will be applied on surfaces where required mortar thickness exceed 25mm. Walls and columns will be plastered 1:4 Cement and Sand to achieve semi rough finished surface. Vertical joint of structural columns / walls & brick walls will be treated by fixing 200mm width chicken mesh with wire nails / concre...
Read more

Method of Plastering

Image
Method of Plastering Internal plastering on surfaces of brick and concrete. External wall plastering. Soffit plastering / Soffit finishing with cement based easy plaster material and wall putty. Improving joint of brick walls & structural concrete joints. Internal Plastering on surfaces of Brick and Concrete Surface where plastering is to be done will be cleaned. Level pegs on walls will be fixed with reference to the off lines to brick walls set out in floors. (Using centre plumb bob and nylon thread). All the brick walls will be watered before pasting mortar on walls. First coat mortar filling (1:4 Cement and Sand) up to 15 mm will be applied on surfaces where required mortar thickness exceed 25mm. Walls and columns will be plastered 1:4 Cement and Sand to achieve semi rough finished surface. Vertical joint of structural columns / walls & brick walls will be treated by fixing 200mm width chicken mesh with wire na...
Read more

CRACK TREATMENT OF THE ASPHALT BINDER COURSE

Image
  Main Break Water(MBW) access road occurs several cracks on the asphalt binder course. The road cracks are monitored and investigated with specialist from RDA Research & Development. This report describes the reason and remedial method of the cracks based on the investigation and consultation. MBW access road structure consists of fallowing cross section and the core samples have been taken on the cracks. According to core sample data, can be observed that the crack was started from CBM and reflected to the binder course surface. CRACK INVESTIGATION The crack survey carried out for the entire road and investigation detail summarized as an attached sheet. Core samples were taken from the jointly selected locations with the engineer. MBW access road cracks were categorized into two types based on crack surface appearance. Transverse cracks Longitudinal cracks ...
Read more

Survey & levelling

Image
    Preliminary work in road construction is surveying & leveling works. This consists of Traverse Survey, TBM Survey, and Centre Line Setting out, Centre Line marking, Cross Section Survey and Submittal of Drawings. Traverse Survey At the commencement of contract all the basic traverse points will be checked and if any are found to be missing or appear to have been disturbed, necessary arrangements should be made to re-establish the points and traverse survey is carried out after that. Establishing TBMS We did not use survey Department bench marks .The permanent concrete cube was selected to permanent bench mark. It height was assumed hundred meters. But this point is not sufficient for construction purposes. So reference to this point Temporary bench marks (TBM) should be established. TBMs are used to transfer reduce levels in road construction. Temporary bench marks should be established at the rate of four per km and also at or near all structures. When e...
Read more